Clipper guard lengths
Choose the guards for the top and sides (and a fade if you want one), then press Calculate for the lengths and the words to use at the barber.
| Guard | Inches | Millimetres | What it gives |
|---|---|---|---|
| No guard (#0) | about 1/32 in | 0.5 to 0.8 mm | Down to stubble; the shortest a clipper goes without a guard. |
| #1/2 | 1/16 in | 1.5 mm | As short as it gets outside of bald; used for skin fades. |
| #1 | 1/8 in | 3 mm | A short buzz cut with the scalp showing. |
| #1.5 | 3/16 in | 5 mm | Between a #1 and a #2; used to blend fades. |
| #2 | 1/4 in | 6 mm | A traditional buzz cut. |
| #3 | 3/8 in | 10 mm | A longer buzz cut; the top of many fades. |
| #4 | 1/2 in | 13 mm | Crew cut or brush cut length. |
| #5 | 5/8 in | 16 mm | Enough length to style with some product. |
| #6 | 3/4 in | 19 mm | Enough to part the top or push the front up. |
| #7 | 7/8 in | 22 mm | Room for a side part, crew cut or Caesar. |
| #8 | 1 in | 25 mm | The longest standard guard; often used on top. |
Where the lengths come from
The inch sizes in the chart follow Wahl’s standard US numbering: a guard cuts any hair longer than its length down to that length, so a #8 leaves 1 inch. Wahl’s UK attachment combs carry the same numbers in millimetres, from #1 at 3 mm through #2 at 6, #3 at 10 and #4 at 13 up to #8 at 25 mm, the figures the chart uses. Andis labels its magnetic comb set the same way, adding 1/16 inch at 1.5 mm.
Labels round because an inch is exactly 25.4 mm (NIST), so each 1/8-inch step is about 3.2 mm. A #3 at 3/8 inch works out to about 9.5 mm, which is why Wahl prints 10 mm on that comb but 9 mm in its optimised comb set.
Without a guard the cut is close to skin. Wahl’s UK guide gives 0.8 mm for its standard blade and about 0.5 mm in its answers to common questions, where it notes that the bare blade is often called a #0. It also warns that guard sizes can differ between brands, so a number on one set is not always the same length on another.
Half guards and the taper lever
A #1.5 sits between a #1 and a #2: Wahl’s UK No. 1.5 comb cuts to 4.5 mm, close to 3/16 inch, and Andis’ 11-comb set includes both 3/16 inch and 3/32 inch for very close blending. Wahl’s UK guide builds a fade from guards between #0 and #4 for a gradual blend from skin to a longer top.
The lever on the side of many clippers adds another step. Moving it from one end to the other changes the length by about 1/16 inch, according to Wahl’s US taper lever guide. At that rate a #1 with the lever open leaves about 3/16 inch, the same as a closed #1.5, and an open #1.5 cuts about the same as a closed #2, which is how the finder adds the lever. Wahl’s own pages describe the up and down positions both ways, so a quick test on a small patch settles which way a given clipper works.
Common guard combinations
Wahl’s US guard guide lists these guard mixes for popular cuts:
| Cut | Sides and back | Top |
|---|---|---|
| Buzz cut | #2 | #2 |
| Fade cut | #1/2 low, #2 higher up | Not set by Wahl |
| Side part | #4 | #8 |
| Textured cut | #3 low, #5 higher up | #8 |
| Brush cut | #1/2 at the front, #1 elsewhere | #7 |
The UK guide gives a #2 or #3 for a classic buzz cut and a #4 on the sides and back for a crew cut. A #8 is the longest guard in most standard sets, though Wahl’s UK range also has a #12 comb at 38 mm, about 1 1/2 inches; anything longer on top is cut with scissors. Lengths and styles for one-length cuts are covered in this guide to buzz cut guard numbers.
A guard cut does not stay that length for long. Hair on the head grows about 1 cm a month, according to Germany’s health information institute IQWiG, so a #1 cut (3 mm) reaches about the length of a #4 (13 mm) within a month.
Asking for a fade
A fade steps down through the guards from the sides to the neckline, and its name says where the short part ends. Mancave Barbershop describes a low fade as reaching about half an inch above the ear, a high fade as blending from high on the head for strong contrast, and a mid fade as sitting between the two. Barbers there recommend bringing photos and pointing to the spot.
Wahl’s advice for home cuts is to start with a longer guard and work down, since hair cannot be put back. For a softer version at the neckline, see how to ask for a low taper at the sides and nape. The finder at the top of this page turns any guard choice into lengths and a sentence to read out at the barber.
