Tie length and suit size
Enter height, chest and waist (measured over a shirt), then press Calculate for the tie length, knot and suit size.
Tie length by height
The tool follows the height guide of tie maker The Tie Bar, which sells ties in three lengths:
| Height | Tie length | Label |
|---|---|---|
| Under 5’7″ | Under 57 inches | Short |
| 5’7″ to 6’1″ | 57 to 58 inches | Standard |
| Over 6’1″ | Over 58 inches | Extra long |
The average American man stands 68.9 inches, just under 5’9″, according to the CDC’s body measurement data, which puts most men in the standard band.
Makers set their own lengths. Vineyard Vines’ tie chart lists its regular ties at 58 inches and its extra long at 63, both 3 1/4 inches wide. Shirtmaker Paul Fredrick’s size guide puts its regular tie at about 57 inches, adds 5 inches for the long option and suggests it for men 6’2″ and taller or with a neck size of 17 1/2 inches or more.
To check a fit at home, The Tie Bar suggests buttoning a well-fitting shirt to the top, tucking it in and fastening the belt, then measuring from the collar button to the middle of the buckle and adding 2 to 3 inches for a standard knot.
Uniform rules can be stricter. The Navy ROTC unit at the University of Notre Dame has its midshipmen tie a double (full) Windsor and keep the bottom of the tie within one inch above the belt buckle, without touching it.
Knots and collars change the length
Bigger knots use more fabric. The four-in-hand takes the least, which makes it a good knot for very tall men and for heavy wool or knit ties. A half Windsor uses a little more, and The Tie Bar says a full Windsor needs 4 to 6 extra inches of tie, so a man of average height who wears one is often better off with an extra long tie.
The collar decides which knot looks right. Shirtmaker Paul Fredrick pairs them like this:
| Collar | Knot that suits it |
|---|---|
| Point or button-down | Four-in-hand (a half Windsor also works) |
| Medium spread | Any knot; the half Windsor fits best |
| Wide spread or cutaway | Full Windsor or half Windsor |
Width follows the jacket: The Tie Bar advises matching the tie to the lapel, from 2 inches for very slim lapels to 3.25 for wide ones. Step-by-step instructions for all three knots are in this guide on tying the four-in-hand and both Windsors.
Suit size from the same measurements
Off-the-rack suit sizes start from the chest. According to Nathan Tailors’ sizing guide, the number is the chest measurement in inches and the letter is the jacket length for the wearer’s height:
| Length | Height | Typical jacket length |
|---|---|---|
| Short (S) | 5’4″ to 5’7″ | 28 to 29.5 inches |
| Regular (R) | 5’8″ to 6’0″ | 30 to 31.5 inches |
| Long (L) | 6’1″ to 6’4″ | 32 to 33.5 inches |
| Extra long (XL) | 6’4″ and up | 34 inches or more |
Brands draw those lines differently. Suit retailer SuitShop treats men under 5’9″ as Short and 6’0″ to 6’4″ as Long, and Paul Fredrick’s chart runs Regular from 5’7″ to 6′ and Long from 6′ to 6’3″, so the tool shows the Nathan Tailors and SuitShop readings when they differ.
Trousers usually come with a 6-inch “drop”: a 40R jacket pairs with a 34-inch waist, and adding 10 gives the European size (a US 40 is an EU 50). Athletic builds run closer to an 8-inch drop and fuller builds closer to 4, which is why some brands cut differently; Kenneth Cole’s suit chart, for one, pairs a 40 jacket with 33-inch trousers. Men whose waist is well off the standard pairing do better with separates or a tailor; the tool flags a gap of 2 inches or more.
For the right length, knot and suit size in one go, enter height, chest and waist in the tool at the top of this page.
